Filters
Expeditionary Building Systems
$0.00
FEATURES:
- Hand-operated desalinator for up to 20 people
- Provides 4.5 litres of water per hour
- Optimum pump frequency: 30 pumps per minute
- Weighs only 7 lbs
$0.00
FEATURES:
- The world's smallest desalinator
- Hand-operated desalinator for 1 - 6 people
- Provides 0.89 litres of water per hour
- Optimum pump frequency: 40 pumps per minute
- Weighs only 2.5 lbs
$0.00
FEATURES:
- The tried and tested ceramic depth filter Katadyn Pocket Tactical removes bacteria, protozoa and other disease-causing agents.
- The microorganisms cannot pass through the pores of the filter ceramic (0.2 microns) because of their size (greater than 0.2 microns = 0.0002 mm).
- Unlike disposable filters, the ceramic can be cleaned several times - even in the field.
- Quickness counts too with an output of 1 litre/minute through our silver-impregnated ceramic filter.
- The capacity is up to 50'000 litres, depending on the water quality.
- The Pocket Tactical is suitable for the toughest of conditions and is the first choice for extreme adventurers.
- Decades of military and emergency professionals around the world have put their trust in the Pocket's ability to deliver water free of bacteria and protozoa.
$0.00
Katadyn Micropur MP1 tablets are the only EPA Registered Purification Tablets on the Market! And the only disinfection system effective against viruses, bacteria, cryptosporidium, and Giardia. No unpleasant taste.
Each tablet purifies one liter (32oz.) of water and is conveniently sealed in an individual child-resistant foil pouch. To use, simply drop one tablet into one liter of water and wait the required time.
They weigh nothing and dissolve fast! Packaging keeps them safe until needed and gives you peace of mind while out having fun. You can survive 3 weeks without food but not more than 3 days without clean water.
$0.00
FEATURES:
- The BeFree 1.0L Tactical is lightweight (73g) and portable for quick deployment.
- It is superlight to fill. This filter removes bacteria, cysts and sediment with its pore size of 0.1 microns (0.0001 mm).
- The collapsible flask packs small to fit into tight spaces.
- The output is up to 2L/min. with a total capacity of 1000L, depending on the water quality.
- Easily clean the EZ-Clean MembraneTM by simply shaking or swishing the filter in the water - in the field or at home. No backflushing or tools necessary. 100% PVC and BPA free.
- Gives you the freedom to drink anytime, anywhere.
$0.00
Freeze-dried outdoor and expedition food. When it comes to food, you seek delicious and nutritious ingredients that will sustain you. With an emphasis on quality, combined with the care that goes into each of our products, you can count on ALPINE AIRE FOODS to fuel your next mission.
$0.00
The Optimus Polaris utilizes nearly any fuel (White gas, LP Gas, Gasoline, Kerosene, Diesel, Jet fuel) you want to give to make sure you have a warm meal ... anytime, anywhere, any weather. The Polaris delivers superior, reliable, one-jet cooking performance with no fiddling to change nozzles or attachments. When using LP Gas canisters, just flip between 4 Season Mode in cold temps and the Efficiency Mode for other use. With the integrated magnetic cleaning needle, the stove can be quickly cleaned, even while cooking.
$0.00
The Multi-Fuel Expeditionary (EX)-Power generator is capable of running on military grade fuels such as JP-8, F-24, JP-5, and JET-A for US Military applications. The Ex-Power 1000 is one man portable (32.9 lbs), quiet, easily maintained, and easily deployed. The Ex-Power 1000 will provide 900 watts of sustained, clean, inverted AC power.
Dimensions: 18'L x 11.5'W x 15'H Specifications:- A/C Output: 0-900W continuous at sea level
- Peak AC Output: 1000W
- Fuel Tank Capacity: 0.6 gallons
- Fuel: JP-8, F-24, JP-5, JET A
- Auto Temperature Control
- Ability to Parallel
- 5-gallon Fuel Extension Kit
$0.00
The Multi-Fuel Expeditionary (EX)-Power generator is capable of running on military grade fuels such as JP-8, F-24, JP-5, and JET-A for US Military applications. The Ex-Power 2000 is one man portable (52 lbs), quiet, easily maintained, and easily deployed. The Ex-Power 2000 will provide 1500 watts of sustained, clean, inverted AC power.
Dimensions: 23'L x 11.5'W x 17'H Specifications:- A/C Output: 0-1500W continuous at sea level
- Peak AC Output: 1500W
- Fuel Tank Capacity: 0.6 gallons
- Fuel: JP-8, F-24, JP-5, JET A
- Auto Temperature Control
- Ability to Parallel
- 5-gallon Fuel Extension Kit
$0.00
The Energy Focus Intellitube® Series LED retrofit tube is our proprietary designed, all-in-one level tube that offers direct-wire (ballast not required) and direct-fit (compatible with ballasts) functions. In direct fit, it can replace an existing fluorescent lamp. In the event of a ballast failure, in direct wire mode, the Intellitube® will require re-wiring to the main power and continue to provide the most efficient light output.
FEATURES:
FEATURES:
- Connection: Medium Bi-Pin (G13) with 90° push-lock rotation option; direct retrofit for T8, T10 and T12 lamps.
- Input Voltage: 110 -277VAC, 50/60Hz.
- Lamp Life: Rated life of 50,000 hours to 70% lumen maintenance.
$0.00
These Globe Fixtures are waterproof, shockproof, and consume 80% less power than incandescent bulbs. After installation, there should be no need to revisit the fixture for maintenance for upwards of ten years. Unlike outdated incandescent technology, the LED Globe Fixtures do not have a filament that breaks often, especially on moving ships. Changing bulbs is not necessary, providing less needed maintenance and more storage space.
FEATURES:
FEATURES:
- Large LED Globe Color Options: White (19W), Red (8W), Amber (19W).
- Small LED Globe Color Options: White, Red, Blue, Amber. (5W).
- NSN's available for each.
$0.00
The Energy Focus brand LED Berth Fixture consumes 50% less power than other legacy Berth Lights; additionally displaying a lifespan of 50,000 hours until it reaches 70% of its original lumen performance. After installation, there should be no need to revisit this fixture for maintenance for upwards of ten years. Changing bulbs is not necessary, providing even less maintenance and more storage space. *Designed to be used with Energy Focus's Military T5 LED Lamp.
FEATURES:
• Available with traditional or USB outlet
• Does not require a starter
• No ballast "hum"
• Legacy T5 can be easily replaced with Energy Focus' T5 LED lamp
• Uses 50% of the energy of legacy fixture
FEATURES:
• Available with traditional or USB outlet
• Does not require a starter
• No ballast "hum"
• Legacy T5 can be easily replaced with Energy Focus' T5 LED lamp
• Uses 50% of the energy of legacy fixture
$0.00
FEATURES:
- Direct replacement for all 12' T5 fluorescent lamps
- No modifications needed for retrofit
- Low power consumption significantly increases life of legacy ballast
- Starter must be removed for normal operation
- Does not contain any hazardous materials
- MIL Qualification: MIL 16377
- Made in the USA
$0.00
The 18" MIL Intellitube® functions normally in two installation modes: direct-wire (ballast not required) and direct-fit (compatible with ballasts). In direct-fit mode, it can replace an existing fluorescent lamp. In the event of a ballast failure, in direct-wire mode, will provide optimal efficiency and eliminate any dependence on a ballast.
FEATURES:
FEATURES:
- Designed for use in all MIL-F-16377/5, /58, /65, /66 fixtures
- Easily 'snaps' into legacy fluorescent fixtures (F15, T12)
- No modifications needed for retrofit
- Lower power consumption significantly increases life of legacy ballast (can operate with existing ballast)
- Requires removal of starter for normal operation
- Contains no mercury
- Drop-in replacement for F15T12 lamps
- MIL Qualification: MIL-DTL-16377
- Complies with ANSI C78.81
- Form Factor: T12 LED Lamp
- Made in the USA
$0.00
24" MIL Intellitube® functions normally in two installation modes: direct-wire (ballast not required) and direct-fit (compatible with ballasts). In direct-fit mode, it can replace an existing fluorescent lamp and run off the existing ballast. In the event of a ballast failure, in direct-wire mode, it will provide optimal efficiency and eliminate any dependence on a ballast.
FEATURES:
FEATURES:
- Designed for use in all MILDTL-16377/8, /11, /12, /57, /73, /74 & /75 fixtures
- Drop in replacement for F20T12& F17T12 lamps
- Can operate with or without a starter
- Can operate with or without ballast
- Compatible with 2 & 3-wire ballasts
- Lower power consumption significantly increases life of legacy ballast
- Contains no mercury
- No fluorescent buzzing or flickering
- Compatible with all existing color sleeves
- ONLY time-tested solution for the fleet with over 400K in service
- MIL Qualification: MIL-DTL-16327
- Form Factor: T12 LED Lamp
- Complies with ANSI C78.81
- Made in the USA
$0.00
46" MIL T12 LED tubular lamp does not require a ballast to function normally (direct-wire installation mode). Provides high efficiency and eliminates any dependence on a ballast.
FEATURES:
FEATURES:
- Designed for use in all MIL-DTL-16377/13 fixtures
- Replacement for the 60W, F48T12/CW/HO fluorescent lamp
- Removal of ballast and starter required for normal operation
- Lamp is compatible with multiple colored filter sleeves
- MIL Qualification: Passed MIL-DTL-16377
- Form Factor: T12 LED Lamp
- Complies with ANSI C78.81
- Made in the USA.
- ONLY hangar bay retrofit solution backed by NAVSEA approval
$0.00
FEATURES:
- Virtually eliminates maintenance schedule of legacy explosion-proof globes
- Red and white versions available
- 80% reduction in energy use compared to legacy solution
- Utilizes legacy bolt pattern
- MIL Qualification: Per MIL-DTL-16377J (SH)
- Explosion-proof tested in accordance with MIL-DTL-16377/25 and UL 844
- Field Replaceable Parts: Globe, Driver, LED Array
- Made in the USA
$0.00
The Flood and Area Light is a mission-ready, energy efficient LED light. Comes in a single or double design where customers can choose the beam angle to accommodate a full flood range or a more specified area range.
FEATURES:
FEATURES:
- Marine use rated
- ABS Type Approved
- Rugged construction to handle demanding environments.
- Longer lasting and better quality of light
- Eliminates time-consuming maintenance.
- Multiple beam angles available to suit environment: 14, 25, 44, 57, 66
- Mounting: Surface/Rotatable/Yoke
- Regulatory Approval: Type (salt water) and UL 844, ABS, UL 1598 and UL 8750
- Made in the USA
$0.00
Eliminate time-consuming maintenance by providing longer lasting and better quality of light.
FEATURES
FEATURES
- Rugged construction to handle demanding environments
- Rated for Hazardous Locations: Class 1, Division 2, Groups A, B, C, D
- Mounting: Vessel and flat mount
- Enclosure Type: Octagonal shape for easy installation
- Regulatory Approval: UL 1598A [Outside Type (salt water)] and UL 844 [Wet Location Listed], ABS, UL
- 1598, and UL 8750
- Made in the USA
$0.00
The EOD Power Management Kit (EOD-PMK) provides everything the EOD technician needs to recharge his batteries and power his kit from any source (solar, vehicle, AC Mains, scavenged energy). Built around the industry-leading SPM-622 intelligent power manager, the compact EOD-PMK includes a foldable solar blanket, adapters to charge BB-2590, PRC-148, PRC-152, DeWalt tool, AA, and CR-123 batteries, and cables to power common EOD radios, tools, and detection equipment. The easy-to-use EOD-PMK quickly charges one to three batteries simultaneously, and powers up to five pieces of gear at once, converting all voltages automatically. Often deployed in the EOD Tech vehicle, the single power manager replaces up to 20 different battery chargers and power adapters, for a huge savings in space and clutter.
$0.00
The Special Forces Power Management Kit (SF-PMK) provides everything the Operator needs to recharge all his batteries and power his kit from any source (solar, vehicle, world-wide AA). Built around the industry-leading SPM-622 intelligent power manager, the lightweight SF-PMK includes a lightweight foldable solar blanket, adapters to charge the most commonly used military and commercial batteries (AA to BB-2590), and cables to power PRC-117, PRC-152, Toughbook, USB and cigarette powered devices, as well as many more. The easy-to-use SF-PMK quickly charges from one to three batteries simultaneously, and powers up to five pieces of gear at once, converting all voltages automatically. The SF-PMK provides all the power conversion and charging the operator needs in the field, saving weight, cube, clutter, and complexity.
$0.00
The SoloPack™ Battery is a low-profile, rechargeable lithium ion battery that packs the energy needed for a 12 hour mission. Weighing approximately a pound, the battery is small enough to fit in a magazine pouch. It's the lightest weight MOTS rechargeable military battery currently in its class, has a small form factor and is compatible with existing kit such as NATO ammo pouches.The rugged SoloPack is designed to plug-and-play, offering a high power density to power currently fielded equipment and reducing the weight burden of carrying spare batteries.
KEY FEATURES:DOWNLOAD SPEC SHEET
KEY FEATURES:
- Highest energy density in its class
- Fits inside M4 magazine pouch
- Push button activated state-of-charge display
- Wide operating temperature
- Compatible with existing chargers and devices
- NettWarrior Compatible
- SMBus v1.1 compatible
- Can be recharged while in-flight when connected to the Squad Power Manager™ (SPM) which is certified safe-to-fly
$0.00
- Power: 22W
- Weight (oz): 17
- Open (in): 25' x 13'
- Folded (in): 8.5' x 6.75' x 1.5'
$0.00
- Power: 33W
- Weight (oz): 21
- Open (in): 25' x 14.75'
- Folded (in): 6.5' x 7.25' x 1.75'
Toll-Free: 866.845.3012
Products advertised for marketing purposes on this site may contain chemicals known to the State of California to cause cancer or reproductive harm. See –
